LED count is the number buyers ask about and the number that tells you least. Two red light therapy beds with identical diode counts can differ severalfold in delivered dose, because output depends on drive current, bin quality, optics, vzdálenost, and thermal management working together.
Vlnová délka, measured rather than printed
Most full-body red light therapy beds combine red emitters in the region of 630 na 660 nanometers with near-infrared emitters around 810 na 850 nanometrů. Ask for spectrometer measurements of the actual production bin rather than trusting a component datasheet, and check the peak wavelength and full width at half maximum. A nominal 660 nanometer emitter supplied in a loose bin can drift several nanometers, and in a device where wavelength is the mechanism, that drift is a clinical and marketing problem, not a cosmetic one.
Ozáření znamená pouze něco s odstupem
Intenzita záření se uvádí v miliwattech na centimetr čtvereční, a údaj bez měřicí vzdálenosti není specifikací. Světlo se vzdáleností rychle klesá, takže hodnota naměřená na povrchu panelu může být několikrát vyšší než hodnota na kůži uživatele. Zeptejte se na vzdálenost, měřicí mřížka, a použitý měřič, pak porovnejte podobné s podobným.
Před porovnáním produktů převeďte na dávku. Fluence v joulech na centimetr čtvereční se rovná ozáření ve wattech na centimetr čtvereční vynásobené dobou expozice v sekundách. Ozáření 50 miliwatty na čtvereční centimetr udržovaný po dobu deseti minut dodává 30 jouly na centimetr čtvereční, protože 0.05 násobeno 600 rovná se 30. Postel propagující velmi vysokou špičkovou hodnotu s dvouminutovou předvolbou může dodat méně celkové energie než skromný panel běžící patnáct minut.
Jednotnost v celé léčebné rovině
Jediný středový bod skryje problém, se kterým se většina uživatelů skutečně potýká: horká místa v blízkosti zářičů a mrtvé zóny mezi nimi. Vyžádejte si devítibodovou nebo dvanáctibodovou mapu napříč použitelnou léčebnou rovinou v zamýšlené vzdálenosti, a podívejte se na poměr mezi nejvyšší a nejnižší hodnotou. Uniformita je také otázkou pohodlí, protože horké místo se stane stížností dlouho předtím, než se stane bezpečnostní zprávou.
Tepelný návrh a pracovní cyklus
Výstup klesá s rostoucí teplotou přechodu, takže chlazení je výkonová specifikace maskovaná jako mechanický detail. Ask what happens during a sixty-minute continuous run at maximum output: how far irradiance drops, what the surface temperature of the panel and mattress reaches, and what the noise level is at one meter.
Then ask for the duty cycle and the derating policy. A bed rated for continuous commercial use in a clinic should not need a rest period between clients, and if it does, that belongs in the manual and in your booking schedule. Driver quality and heatsink design determine whether output at month eighteen resembles output on day one, and LED maintenance projections such as LM-80 data with TM-21 extrapolation are the evidence for that claim.
Ovládací prvky, dosing, and software
A professional bed should let the operator set a dose rather than only a timer, and it should prevent accidental overexposure through preset limits and session lockouts. Session logging, user accounts, and exportable treatment records matter to clinic buyers and to your own post-market surveillance.
Ask how firmware is updated, whether the update is validated, and whether the device locks if an update fails. Where software contributes to the device’s safety or performance, IEC 62304 defines the lifecycle expectations your technical file will be measured against, and a red light therapy bed supplier with no software documentation is a supplier you will have to re-engineer later.