Какие характеристики наиболее важны для кровати для терапии красным светом?

Дом

>

Часто задаваемые вопросы

>

Какие характеристики наиболее важны для кровати для терапии красным светом?

Количество светодиодов — это число, о котором спрашивают покупатели, и число, которое говорит вам меньше всего.. Две кровати для терапии красным светом с одинаковым количеством диодов могут в несколько раз отличаться по доставляемой дозе., поскольку выход зависит от тока привода, качество бункера, оптика, расстояние, и управление температурным режимом работают вместе.

Длина волны, измеряется, а не печатается

Большинство кроватей для терапии красным светом всего тела оснащены красными излучателями в районе 630 к 660 нанометров с излучателями ближнего инфракрасного диапазона вокруг 810 к 850 нанометры. Запросите спектрометрические измерения фактического производственного бункера, а не доверяйте спецификации компонента., и проверьте пиковую длину волны и полную ширину на половине максимума. Номинальный 660 нанометровый излучатель, поставляемый в неплотной упаковке, может дрейфовать на несколько нанометров., и в устройстве, где длина волны является механизмом, этот дрейф является клинической и маркетинговой проблемой, не косметический.

Irradiance only means something with a distance

Irradiance is quoted in milliwatts per square centimeter, and a figure without a measurement distance is not a specification. Light falls off rapidly with distance, so a value taken at the panel surface can be several times higher than the value at the user’s skin. Ask for the distance, the measurement grid, and the meter used, then compare like with like.

Convert to dose before comparing products. Fluence in joules per square centimeter equals irradiance in watts per square centimeter multiplied by exposure time in seconds. Излучение 50 milliwatts per square centimeter maintained for ten minutes delivers 30 joules per square centimeter, because 0.05 multiplied by 600 equals 30. A bed advertising a very high peak figure with a two-minute preset may deliver less total energy than a modest panel running for fifteen minutes.

Uniformity across the treatment plane

A single center-point reading hides the problem most users actually experience: hot spots near the emitters and dead zones between them. Request a nine-point or twelve-point map across the usable treatment plane at the intended distance, and look at the ratio between the highest and lowest readings. Uniformity is also a comfort issue, since a hot spot becomes a complaint long before it becomes a safety report.

Thermal design and duty cycle

Output falls as junction temperature rises, so cooling is a performance specification disguised as a mechanical detail. Ask what happens during a sixty-minute continuous run at maximum output: how far irradiance drops, what the surface temperature of the panel and mattress reaches, and what the noise level is at one meter.

Then ask for the duty cycle and the derating policy. A bed rated for continuous commercial use in a clinic should not need a rest period between clients, and if it does, that belongs in the manual and in your booking schedule. Driver quality and heatsink design determine whether output at month eighteen resembles output on day one, and LED maintenance projections such as LM-80 data with TM-21 extrapolation are the evidence for that claim.

Элементы управления, dosing, and software

A professional bed should let the operator set a dose rather than only a timer, and it should prevent accidental overexposure through preset limits and session lockouts. Session logging, user accounts, and exportable treatment records matter to clinic buyers and to your own post-market surveillance.

Ask how firmware is updated, whether the update is validated, and whether the device locks if an update fails. Where software contributes to the device’s safety or performance, МЭК 62304 defines the lifecycle expectations your technical file will be measured against, and a red light therapy bed supplier with no software documentation is a supplier you will have to re-engineer later.

Сопутствующие устройства для терапии красным светом

Показ слайда 1 из 25: Панель для терапии красным светом P4-4

Отправьте нам сообщение

Чтобы узнать больше о нашей продукции, приобрести кровати и оборудование для терапии красным светом, мы можем предоставить комплексное обслуживание OEM/ODM, или хотите стать нашим дистрибьютором/агентом, пожалуйста, оставьте сообщение!

Делиться:

Оглавление

Связаться с нами

Оставьте нам сообщение о том, что вам нужно, например каталог, и решение. Наш ответ на ваши вопросы гарантируется как можно скорее в течение 24 часы.

*Вся ваша информация уважаема & защищен в Америке.

Свяжитесь с нами, чтобы получить каталог & цитировать

*Пожалуйста, убедитесь, что подлинность информации, заполненной для нашего удобства в обслуживании вас!*Вся ваша информация защищена компанией Merican..